Skip to main content
Go to accessibility notice

    Description

    "Enigma" Encrypting Machine Used by the German Military in WWII.
    Enigma machines, the vast majority of which were destroyed by Nazi Germany to prevent them falling into the hands of the Allies, were used during the war to send and receive encrypted messages. The three cipher rotor design, dubbed "M3", was used from 1934 until the end of the war. Considered nearly "unbreakable", its only inherent flaw, beyond human error, which would ultimately be its downfall, was the fact that the machine could scramble the letters into any one of 17,576 combinations except the use of the original letter. However, it would be human error, such as signing off each communication with "Heil Hitler" (as showcased in "The Imitation Game"), that allowed the Allies to deconstruct many of the cipher's coded communications. Though widely employed by Germany during the war, enigma machines are now very scarce, as those not destroyed now rest in unknown watery graves. Additionally, Winston Churchill ordered all enigma machines to be destroyed at the end of war. Not more than 250 used during WWII are now believed to still exist, with machines having matching parts, such as this example, even more rare!

    The present machine is model M3 with the serial numbers of the rotors matching the machine itself (since the rotors were interchangeable, this isn't always the case). The serial number engraved on the plate attached to the keyboard reads "A/ 00660/ bac/ 43 E", matching the serial number "660" stamped on the plate underneath the rotors and also matching the serial number on the rotors themselves. The metal wheels also bear the engraving of the Third Reich emblem - a black eagle above a swastika. Upon the interior of the wooden lid are the operating instructions in German, above the "QWERTZUIO" mechanical keyboard which would light up when in operation. Twenty-six bulbs exist on the lamp board, with one broken. The socket locations are marked "Kabelprufung" (cable test) and "Lampenprufung" (lamp test). The original battery is still present, with expected corrosion. Part of the leather strap is also present, but no longer secured to the wooden case. All in all, an exceptionally fine & original example of this most iconic World War II artifact. Always in high demand, sales have been recorded in excess of $100,000. The entire machine and case weigh approximately 28.5 lbs. and measures 11" x 13.25" x 6".


    More Information: Translation of the label inside the lid of the wooden case:

    Please note!
    Refer to the instruction manual for the cipher machine (H. Dv. G. 13)
    1. To clean the roller contacts, turn each roller forward and backward several times.
    2. To clean the key contacts, press all keys vigorously several times before switching on the power. Suppress and rock it up, keeping one button pressed.
    3. When adjusting the signs visible in the windows, make sure that the rollers are properly locked.
    4. The unmistakable double-pole connectors are to be inserted all the way into their socket pairs. The front wooden flap should then be closed, otherwise 3 lamps may light up at the same time.
    5. If no lamp lights up when the button is pressed, the battery, its contact springs, its connections are on To check the changeover switch and the changeover switch.
    6. If one or more lamps do not light up when the button is pressed, the corresponding lamps are the Contacts underneath, the cables of the double-pole connectors, the sockets including their end plates, the roller contacts, the working contacts under the respective pressed keys and the idle contacts under the keys corresponding to them, and to clean up dirt and oxidation. (See also point 2).
    From machine no. A 4388 from the opening on the right side of the lamp field is used for lamp test.
    Starting from machine No. A 4388, the outermost left and right bushings of the middle one are used for cable testing Row on the plug board and the cable test lamp on the left side of the lamp field.
    7. Roll axis and roller bushes are to be kept clean and like all other bearing points and lightly grease again with resin- and acid-free oil. The fixed contacts of the rollers are all Sand over for 6-8 weeks with polishing paper and rub with a little soaked oil. The key contacts, the lamp contacts and the short circuit plates must be protected against oiI.
    8. Key information is given either by numbers or letters.
    To convert the numbers into letters or vice versa, the following table is used:
    A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
    01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26


    Auction Info

    Proxy Bidding Ends
    December
    14th Saturday 10:50 am CT
    Auction Dates
    December
    14th Saturday
    Proxy Bidding Time Remaining
    4 Days 18h 1m 25s
    Bids + Registered Phone Bidders: 14
    Lot Tracking Activity: 125
    Page Views: 3,541

    Buyer's Premium per Lot:
    25% on the first $300,000 (minimum $49), plus 20% of any amount between $300,000 and $3,000,000, plus 12.5% of any amount over $3,000,000 per lot.

    This lot is in: 1 - Signature® Floor Session (Live Floor, Live Phone, Mail, Fax, Internet, and Heritage Live):
    (Lots 42001-42188) - 11:00 AM Central Time, Saturday, December 14, 2019.
    (Proxy bidding ends ten minutes prior to the session start time. Live Proxy bidding on Heritage Live starts 24 hours before the live session begins and continues through the session.)

    Show All Session Information

    Show Auction Type Info

    Exhibition Viewing Times, Title Page, Floor Session and License Information

    Additional Location Info:
    Heritage Auctions - Dallas
    3500 Maple Ave
    17th Floor
    Dallas, TX 75219

    Current Bid:
    $82,500
    Bid Protection
    w/ Buyer's Premium (BP) : $103,125.00 Minimum Next Bid: $85,000 ($106,250.00 w/ BP)
    Track Item